Wire the LCD RKP as shown in the wiring section of this manual. Replace the .. The Eurosec CP8 LCD has two log modes. These are: a). gardtec eurosec cpx installation manual · Home · Blog · About · Press · Contact · Home · Blog · About · Press · Contact. Powered by カスタマイズ可能なテンプレート . A range of alarm system user guides and manuals for owners and clients. Accenta 6 · Euro 46 User Manual · Euro Mini User Guide · Eurosec CP7/CP8 LED .

Author: Durisar Dura
Country: Niger
Language: English (Spanish)
Genre: Video
Published (Last): 25 June 2006
Pages: 276
PDF File Size: 10.97 Mb
ePub File Size: 13.72 Mb
ISBN: 180-8-55932-673-5
Downloads: 6065
Price: Free* [*Free Regsitration Required]
Uploader: Moogubar

At the end of the message you will hear a single tone, at this point press a key on your telephone keypad twice. Local legislation may prevent the use of Duress signals. Please refer to the Using G-Tag section for instructions. To initiate the Remote Call follow the instructions below. Under no circumstances should the actual user code be written down. I mean do some kind of connection or make any changes through the keypad? Remember me This is not recommended for shared computers.

If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call usually on lines with incoming calls barred.

It should be noted that VoComm should not under any circumstances be used to ring the Emergency Services directly. If you require a blank space press YES while the ‘-‘ is displayed 14 As you press YES for the ninth character or if you have jumped from step 9 the display will change to: To program a Control Code level.

To unset repeat this operation. At this point it is essential that you contact your installation company. Before attempting to reset your system ensure that the system is Un-set. The display will clear once the power is restored.


Check line is not in use or disconnected etc. Duress Codes may also be used on this system for activating Personal Alarms P.

User Manuals – Smith Security

The term Open relates to the system being Unset. Before Vo-Comm can work several options will need to be programmed. If you do not choose to Set or Unset the system within the ten seconds the top line of the display will be blanked out and the code entry will be invalidated. Read Log 01 JAN The Proximity Reader may be built in to the keypad or be an external reader that is fitted into a doorframe etc.

More than 24 key presses will cause a keypad tamper. Page 7 Enter Zone No. If the code already exists or is a duress of another code an error will be shown, choose another code and return to step 6 7 The display will show: In this instance using will send a Duress code to your central station when you Set or Unset your system.

In the event of a sustained power cut the system battery will continue to supply the system until the battery voltage falls to a set point, at his stage the display will show: Zone remove is only effective for the one set. To unset insert the key and turn to the OFF position.

You may check the Status of the system at any time by pressing the Yes key and then entering a valid User Code. Normal To set the system with a normal keyswitch, insert the key and turn to the ON position then remove the key. My order number is if you could kindly send me the engineer manual please.

Control Allows an output that has been pre-programmed by the installation company to be operated.

If the system was Unset only the internal sounders will operate. Vo-Comm messages may be sent to standard land line telephones or mobile telephones. See Advanced Code Programming section for details. Servicing may also be a requirement of you insurance policy. The display will show: The CPX is capable of using two methods to activate the Duress signal. Instxllation the normal instructions to the end for programming codes.


At this point eueosec you Tag to the Proximity Reader and a code will be entered for you. Follow the instructions for programming User Codes onto your system up to the point when you would enter the User Code.

Posted 31 December – A Master level code may change the status of the Chime between On and Off. Your installation company will give training on the use of the equipment in order to comply with the relevant standards and will be able to answer specific questions about your system, request for additional or installation staff training should be directed to your installation cpxx. Pressing YES will move forward to the next event.

Whilst viewing the Log, Pressing NO will move back to the previous event. If the system was Set when you did this the display will ask if you wish Unset the system. The alarm may be silenced by entering a valid User Eutosec. Press No until the require level of code is shown Refer to page 3 for code level details.


The top line of the display will then be blanked off. Then choose Can or Cant Unset dependant on your requirements. Press No until the setting you require is displayed Yes janual No. When the premises are secure listen that the exit tone returns to the continuous tone. This also applies to cut cables.